Sold Out
When you want astonishing results for less cost than many other brands - PrimaCreator VALUE resin should be your first choice.
Sold Out
When you want astonishing results for less cost than many other brands - PrimaCreator VALUE resin should be your first choice.
€89.90 Incl. VAT
PrimaCreator Direct Drive Extruder for CR10/Ender 3 series
*Without motor
Notice! Manufactures sometimes change the hardware on printers. Make sure that the feeding gear can be removed from the motor shaft. If you cannot remove the stock feeding gear, you need to replace the motor. *There is no motor included in the package
€22.43 Incl. VAT
PrimaSELECT™ PLA Chameleon is a new filament from PrimaCreator with a unique look. The filament is made up from two strands of filament which results in a print that has dual colors. The effect is stunning as the print seems to “change color” as you turn it and the light reflects in different ways.
€29.90 Incl. VAT
SELECT NylonPower PA 6/66
is a special co-polymer blend that’s take full advantage of the strengths of both PA 6 and PA66. The combination of these two types of PA makes our Nylon very easy to print. Normally Nylon (PA) is very hard to print with and has a hard time sticking to the build plate. With NylonPower you can use lower print temperatures than you normally would with Nylon. This means that you can use this material in most common printers on the market.
When printing with Nylon you should do so on a heated build plate. For best adhesion we recommend that you use Magigoo PA. The temperature should be set to 60-80°C.
Nylon has strong mechanical strength and deforms less. It´s hard to snap of or break. Nylon is also one of the best materials when it comes to impact resistance.
Nylon is very hydroscopic. This means that it absorbs liquids, this could be a benefit if you want to dye your filament. It also means that it is important to dry your Nylon before use. You can set the oven at 70-80°C and leave it there for 4-8 hours. The longer you leave it, the more dryer it will be and that will also reflect on the finished print result, both visual and performance wise.
is the latest generation of high performance material for your 3D Printer. Our SELECT NylonPower is based on Nylon 12 and is reinforced with 16 % glass fibers. This makes for an extremely tough filament that is perfect for printed parts that can be used in the automotive industry, drones and RC parts. The glass fibers make it a bit softer and not as rigid as the version with carbon fibers.
€59.90 Incl. VAT
When you want astonishing results for less cost than many other brands - PrimaCreator VALUE resin should be your first choice.
€49.90 Incl. VAT
When you want astonishing results for less cost than many other brands - PrimaCreator VALUE resin should be your first choice.
€9.99 Incl. VAT
5-Pack or 25-Pack of high quality resin filters. The filters are used to filter out any debris, particles, cured resin pieces or other contamination that's made it way into the resin.
€3.99 Incl. VAT
5-Pack or 25-Pack of high quality resin filters. The filters are used to filter out any debris, particles, cured resin pieces or other contamination that's made it way into the resin.
€79.90 Incl. VAT
PrimaSELECT™ PLA Matt is a very nice 3D Print material, it's non-toxic and has a no unpleasant smell when you print with it. Because of its thermal characteristics it's easy to get great prints. Filament from PrimaCreator comes on a transparent spool which makes it easy to see how much filament there are left on the spool.
€59.90 Incl. VAT
The All Metal Hot-End from PrimaCreator is the perfect addition for your Creality 3D Printer.
It's a very smart “drop in” conversion kit for your printer. You don't need to make any modifications to your printer and it's very easy to install in minutes!
The cooling block don't have any thermal (PTFE) tube and this makes for a much faster cooling effect and a more stable control.
View full product details
Sold Out
The All Metal Hot-End from PrimaCreator is the perfect addition for your Creality 3D Printer.
It's a very smart “drop in” conversion kit for your printer. You don't need to make any modifications to your printer and it's very easy to install in minutes!
The cooling block don't have any thermal (PTFE) tube and this makes for a much faster cooling effect and a more stable control.
View full product details
€23.99 Incl. VAT
5-Pack of high quality PrimaCreator FEP film sheets.
PrimaCreator FEP film sheets are made of high quality material to ensure high light transmittance and good reliability. To protect the sheets from wrinkles and scratches, each sheet comes with a protective film on both sides and are packaged in a protective envelope.
The sheets fits most 3D-printers using 5,5"-6,1" LCDs.
Sold Out
Roll of high quality PrimaCreator FEP film.
PrimaCreator FEP film sheets are made of high material to ensure high light transmittance and good reliability. To protect the sheet from wrinkles and scratches, each sheet comes with a protective film on both sides and are packaged in a sturdy cardboard tube.
This sheet can easily be cut to fit almost any 3D-printer.
Sold Out
FlexPlate Powder Coated PEI from PrimaCreator is a reusable, relatively maintenance free, build surface for better adhesion and less warping.
The FlexPlate can withstand temperatures up to 130°C without any problems, so you can even use it with ABS.
€34.90 Incl. VAT
PrimaSELECT™ Tough PLA we used the well known SELECT PLA formula and changed it. The result is a new kind of filament that we call “Tough” It has been engineered for strength and durability and put up a fight against ABS.
Sold Out
EasyPrint PLA is our latest PLA and is made from 100% virgin PLA pellets. PLA is one of the most versatile and easy to use filaments on the market. With the right settings you can print parts that is very strong, and it also have a nice shiny surface. PLA is perfect for detailed prints.
€29.90 Incl. VAT
PrimaSELECT™ PLA Satin is a very nice 3D Print material, it's non-toxic and has a no unpleasant smell when you print with it. Because of its thermal characteristics it's easy to get great prints. Filament from PrimaCreator comes on a transparent spool which makes it easy to see how much filament there are left on the spool.
€20.93 Incl. VAT
PrimaSELECT™ PLA Matt is a very nice 3D Print material, it's non-toxic and has a no unpleasant smell when you print with it. Because of its thermal characteristics it's easy to get great prints. Filament from PrimaCreator comes on a transparent spool which makes it easy to see how much filament there are left on the spool.
€29.90 Incl. VAT
PrimaSELECT™ PLA Matt is a very nice 3D Print material, it's non-toxic and has a no unpleasant smell when you print with it. Because of its thermal characteristics it's easy to get great prints. Filament from PrimaCreator comes on a transparent spool which makes it easy to see how much filament there are left on the spool.
€29.90 Incl. VAT
PrimaSELECT™ PLA Glossy is a very nice 3D Print material, it's non-toxic and has a no unpleasant smell when you print with it. Because of its thermal characteristics it's easy to get great prints. Filament from PrimaCreator comes on a transparent spool which makes it easy to see how much filament there are left on the spool.
€17.90 Incl. VAT
PrimaCreator Resin Cleaner is an effective IPA alternative for cleaning of resin printed 3D models.
€7.90 Incl. VAT
A great collection of cleaning tools for nozzles.
A great collection of cleaning tools for nozzles.
€23.90 Incl. VAT
The must-have tools for 3D printing!
Perfect tool kit for the 3D printer.
Lightweight box for easy transport.
€22.32 Incl. VAT
When you want astonishing results for less cost than many other brands - PrimaCreator VALUE resin should be your first choice.
€23.92 Incl. VAT
When you want astonishing results for less cost than many other brands - PrimaCreator VALUE resin should be your first choice!